一、描述你遇到的问题
在开启sle-uart跑流模式后，跑流统计打印2-3次后便断开连接。
二、你具体做的所有步骤结果截图
三、当前开发板状态全景照片
请插入图片
四、开发板串口所有日志
server端日志：
[13:35:24.505]收←◆boot.
[13:35:24.694]收←◆Flashboot Init!
Power On
Reboot cause:0xF0F0
Reboot count:0x0
Reboot count:0x0
Flash Init Succ!
No need to upgrade...
Jump to app! addr = 0x90115300
Debug uart init succ:80000
version: BS2X 1.0.11
This sdk only for BearPi_Pico H2821 development board !
Powered by www.bearpi.cn
cpu 0 entering scheduler
LOS_QueueCreate queueId 0
LOS_QueueCreate queueId 1
[13:35:24.805]收←◆bt at register ret = 80000005
bt at register ret = 80000005
Clock config succ.
[ACore] sle enable cbk in, result:0
sle enable
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
sle enable: 0
[sle uart server] sle uart add service in
[sle uart server] sle uart add service, server_id:1, service_handle:1, property_handle:2
[sle uart server] sle uart add service out
[sle uart server] sle_uart_local addr: 0x00 0x00 0x00 0x00 0x00 0x00
[ACore] sle set announce param, handle:1, mode:3, min_interval:c8, max_interval:c8, tx_power: 0
[ACore] sle set announce param, own addr:0x00::::00:00
[ACore] sle set announce param, peer addr:0x00::::00:00
[sle uart server] data.announce_data_len = 6
[sle uart server] data.announce_data: 0x01 0x02 0x01 0x02 0x02 0x00
[sle uart server] local_name_len = 15
[sle uart server] local_name: 0x73 0x6c 0x65 0x5f 0x75 0x61 0x72 0x74 0x5f 0x73 0x65 0x72 0x76 0x65 0x72
[sle uart server] data.seek_rsp_data_len = 20
[sle uart server] data.seek_rsp_data: 0x0c 0x02 0x0a 0x10 0x0b 0x73 0x6c 0x65 0x5f 0x75 0x61 0x72 0x74 0x5f 0x73 0x65 0x72 0x76 0x65 0x72
[sle uart server] set announce data success.
[ACore] sle start announce in, adv_id:1
[ACore] sle adv cbk in, event:0 status:0
[ACore] sle adv cbk in, event:1 status:0
[ACore] sle adv cbk in, event:2 status:0
[ACore] sle adv cbk in, event:3 status:0
[pm_sys]pm_sys_entry.
[13:35:25.038]收←◆[sle uart server] init ok
sle low latency tx register cb
[13:35:25.062]收←◆[Connected]
addr:ee::::8d:5c, handle:00
[ACore] sle adv cbk in, event:7 status:0
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x1, pair_state:0x1, disc_reason:0x0
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[sle uart server] sle_low_latency_tx_enable
[sle uart server] sle announce terminal callback id:01
[13:35:26.709]收←◆low latency evt handle addr:ee:::**:8d:5c, enable:1, role:1, rate:2000
[sle uart server] sle_set_mcs success
general tx enable!
[13:35:28.226]收←◆[sle uart server] pair complete conn_id:00, status:0
[sle uart server] pair complete addr:ee:::**:8d:a0dff
[13:35:33.305]收←◆[Disconnected]
addr:ee::::8d:5c, handle:00
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x2, pair_state:0x3, disc_reason:0x7
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[ACore] sle start announce in, adv_id:1
[ACore] sle adv cbk in, event:0 status:0
[ACore] sle adv cbk in, event:1 status:0
[ACore] sle adv cbk in, event:2 status:0
[ACore] sle adv cbk in, event:3 status:0
[sle uart server] sle announce enable callback id:01, state:0
[13:35:33.459]收←◆[Connected]
addr:ee::::8d:5c, handle:00
[ACore] sle adv cbk in, event:7 status:0
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x1, pair_state:0x1, disc_reason:0x0
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[sle uart server] sle_low_latency_tx_enable
[sle uart server] sle announce terminal callback id:01
[13:35:34.780]收←◆low latency evt handle addr:ee::::8d:5c, enable:1, role:1, rate:2000
[sle uart server] pair complete conn_id:00, status:0
[sle uart server] pair complete addr:ee::::8d:a0dff
[13:35:39.885]收←◆[Disconnected]
addr:ee::::8d:5c, handle:00
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x2, pair_state:0x3, disc_reason:0x7
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[ACore] sle start announce in, adv_id:1
[ACore] sle adv cbk in, event:0 status:0
[ACore] sle adv cbk in, event:1 status:0
[ACore] sle adv cbk in, event:2 status:0
[ACore] sle adv cbk in, event:3 status:0
[sle uart server] sle announce enable callback id:01, state:0
[13:35:40.210]收←◆[Connected]
addr:ee::::8d:5c, handle:00
[ACore] sle adv cbk in, event:7 status:0
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x1, pair_state:0x1, disc_reason:0x0
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[sle uart server] sle_low_latency_tx_enable
[sle uart server] sle announce terminal callback id:01
[13:35:41.542]收←◆low latency evt handle addr:ee:::**:8d:5c, enable:1, role:1, rate:2000
[13:35:41.592]收←◆[sle uart server] pair complete conn_id:00, status:0
[sle uart server] pair complete addr:ee:::**:8d:a0dff
[sle uart server] ssaps ssaps_mtu_changed_cbk callback server_id:0, conn_id:0, mtu_size:208, status:0
[13:35:52.107]收←◆[Disconnected]
addr:ee::::8d:5c, handle:00
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x2, pair_state:0x3, disc_reason:0x10
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[ACore] sle start announce in, adv_id:1
[ACore] sle adv cbk in, event:0 status:0
[ACore] sle adv cbk in, event:1 status:0
[ACore] sle adv cbk in, event:2 status:0
[ACore] sle adv cbk in, event:3 status:0
[sle uart server] sle announce enable callback id:01, state:0
[13:35:52.236]收←◆[Connected]
addr:ee::::8d:5c, handle:00
[ACore] sle adv cbk in, event:7 status:0
[sle uart server] connect state changed callback conn_id:0x00, conn_state:0x1, pair_state:0x1, disc_reason:0x0
[sle uart server] connect state changed callback addr:ee::::8d:a0dff
[sle uart server] sle_low_latency_tx_enable
[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, sinal callback id:01
[13:35:53.554]收←◆low latency evt handle addr:ee::::8d:5c, enable:1, role:1, rate:2000
[sle uart server] pair complete conn_id:00, status:0
[sle uart server] pair complete addr:ee::::8d:a0dff
[sle uart server] ssaps ssaps_mtu_changed_cbk callback server_id:0, conn_id:0, mtu_size:208, status:0
client端日志：
[13:35:24.104]收←◆\0
[13:35:24.429]收←◆boot.
[13:35:24.632]收←◆Flashboot Init!
Power On
Reboot cause:0xF0F0
Reboot count:0x0
Reboot count:0x0
Flash Init Succ!
No need to upgrade...
Jump to app! addr = 0x90115300
Debug uart init succ:80000
version: BS2X 1.0.11
This sdk only for BearPi_Pico H2821 development board !
Powered by www.bearpi.cn
cpu 0 entering scheduler
LOS_QueueCreate queueId 0
LOS_QueueCreate queueId 1
[13:35:24.753]收←◆bt at register ret = 80000005
bt at register ret = 80000005
Clock config succ.
[ACore] sle enable cbk in, result:0
sle enable
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
bt at register ret = 80000005
sle enable: 0.
uart recv low latency data register success
sle low latency rx register cb
[pm_sys]pm_sys_entry.
[13:35:24.941]收←◆[adv_report] event_type: 0x03, addr_type: 0x0000, addr: 00:::**:00:00
[adv_report] data length: 6, data: 0x01 0x02 0x01 0x02 0x02 0x00
[sle uart client] sle uart scan data :
[13:35:25.000]收←◆[sle uart client] sle uart scan data :
[adv_report] event_type: 0x0b, addr_type: 0x0000, addr: 00:::**:00:00
[adv_report] data length: 20, data: 0x0c 0x02 0x0a 0x10 0x0b 0x73
[sle uart client] sle uart scan data :
sle_uart_server ?
[13:35:25.062]收←◆[Connected]
addr:00:::**:00:00, handle:00
[sle uart client] conn state changed disc_reason:0x0
[sle uart client] SLE_ACB_STATE_CONNECTED
[13:35:25.571]收←◆[sle uart client] sle_set_phy_param success
[13:35:26.573]收←◆[sle uart client] sle_low_latency_rx_enable
[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[13:35:26.693]收←◆low latency evt handle addr:00:::**:00:00, enable:1, role:0, rate:2000
general rx enable!
[13:35:27.227]收←◆recv_len = 250, recv_count = 1000
diff time:508464us, throughput:3937kbps
[13:35:27.743]收←◆recv_len = 250, recv_count = 1000
diff time:514496us, throughput:3891kbps
[13:35:28.227]收←◆[Disconnected]
addr:00:::**:00:00, handle:00
[sle uart client] conn state changed disc_reason:0x1b
[sle uart client] SLE_ACB_STATE_DISCONNECTED
[13:35:33.391]收←◆[sle uart client] sle uart scan data :
[sle uart client] sle uart scan data :
sle_uart_server悘
[13:35:33.459]收←◆[Connected]
addr:00:::**:00:00, handle:00
[sle uart client] conn state changed disc_reason:0x0
[sle uart client] SLE_ACB_STATE_CONNECTED
[sle uart client] sle_set_phy_param success
[13:35:34.644]收←◆[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[sle uart client] sle_low_latency_rx_enable
[13:35:34.786]收←◆low latency evt handle addr:00::::00:00, enable:1, role:0, rate:2000
[Disconnected]
addr:00::::00:00, handle:00
[sle uart client] conn state changed disc_reason:0x1b
[sle uart client] SLE_ACB_STATE_DISCONNECTED
[13:35:40.026]收←◆[sle uart client] sle uart scan data :
[sle uart client] sle uart scan data :
sle_uart_server4?
[13:35:40.210]收←◆[Connected]
addr:00:::**:00:00, handle:00
[sle uart client] conn state changed disc_reason:0x0
[sle uart client] SLE_ACB_STATE_CONNECTED
[sle uart client] sle_set_phy_param success
[13:35:41.391]收←◆[LL] read low latency param cbk:
[LL] tx_addr: 0x59413868, num: 7, size: 268
[LL] rx_addr: 0x59413868, num: 7, size: 268
[sle uart client] sle_low_latency_rx_enable
[13:35:41.558]收←◆low latency evt handle addr:00:::**:00:00, enable:1, role:0, rate:2000
[13:35:41.597]收←◆[sle uart client] pair complete conn_id:0, addr:00***0000
ssapc exchange info, conn_id:0, err_code:0
[sle uart client] exchange_info_cbk,pair complete client id:0 status:0
[sle uart client] exchange mtu, mtu size: 520, version: 1.
discovery character cbk in
discovery character cbk complete in
[sle uart client] sle_uart_client_sample_find_property_cbk, client id: 0, conn id: 0, operate ind: 5, descriptors count: 1 status:0 property->handle 2
[sle uart client] sle_uart_client_sample_find_structure_cmp_cbk,client id:0 status:0 type:3 uuid len:0